MUTOH PJ-2216NXE Guia do Utilizador Página 8
- Página / 266
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA
April 2002
PJ16E-A-00d 7 MUTOH INDUSTRIES LTD.
3.4.2 Turning the power OFF
p.3-9−p.3-11 Modify the procedures as follows:
1. Follow “3.8 Test printing”, and perform nozzle check printing.
2. Verify if there is any clogging of nozzles, missing dots, or faint printing.
NOTE
NOTE
If printing quality declines, or if missing dots are evident after the nozzle check, the print heads need
to be cleaned.
See “4.5.4 Head cleaning” to perform head cleaning.
If turning the power OFF without head cleaning, the clogged nozzle may not restore.
3. Verify the following regarding the operational condition of the product.
There is no printing operation being performed.
The control panel is in a normal status.
4. Push the [POWER] key of the control panel, to turn the product OFF
NOTE
NOTE
The power is ON if the control panel displays the following conditions:
・
The [POWER] key is in the pushed-in condition.
・
The POWER lamp is lit (red)
Press the [POWER] key again to turn the power OFF.
F 1
F 3
F 2
F 4
ERROR
DATA
MEDIA SET
CANCEL ENTER
POWER
MENU
RECEIVE
PROCESS
5. The product will perform the power OFF operation.
Following message is displayed on the operation panel.
- PJ-1614NXE 1
- PJ-2216NXE 1
- 3.4.1 Turning the power ON 6
- 3.4.2 Turning the power OFF 8
- April 2002 10
- 3.6.5 Setting winding unit 21
- 3.6.6 Setting media type 22
- Alignment Uni-D 25
- Media feeding direction 29
- Drawing start point 29
- 4.4.38 Utility menu 32
- 4.4.64 Winding Unit Menu 33
- 4.4.65 Send Roll menu 34
- (1) Replacement interval 38
- (2) Replacement procedure 38
- 6.3.1 Status messages 44
- <MEMO> 45
- Important Notice 49
- About This Manual 52
- GENERAL TABLE OF CONTENTS 53
- 7 Appendix 56
- 1 SAFETY INSTRUCTIONS 59
- Safety terms Details 61
- 1.4 Warning labels 67
- No. Type 68
- 2 PRODUCT OVERVIEW 69
- 2 Product Overview 71
- No. Name Function 72
- No. Position Description 77
- 3 BASIC INSTALLATION 81
- 3 Basic Installation 83
- 86
- 86
- 98
- 3.6 Media handling 99
- No. Name 100
- • The media type is set 119
- 120
- 120
- 120
- 120
- • Ink Color: All 121
- • Purge mode: Normal 121
- 3.8 Testprinting 124
- 3.8.1 Setup List 125
- 3.8.2 NozzleCheck 126
- 3.8.3 Alignment 127
- 128
- 128
- 3.9.1 System requirements 131
- 3.9.2 Selecting cables 131
- 4 HANDLING THE 133
- 4 Handling the printer 135
- 4.3 Using media 137
- 4.3.4 The printing area 138
- (1) PJ-1614NXE 139
- (2) PJ-2216NXE 139
- 4.3.6 Media feed compensation 141
- 4.4.1 Setup menu 143
- 4.4.2 Origin setup menu 145
- 4.4.3 Test print menu 146
- 4.4.4 Media setup menu 147
- 4.4.5 Media type menu 147
- 4.4.6 User media menu 148
- 4.4.7 InkDry menu 150
- 4.4.8 HeadHeight menu 150
- 4.4.9 Stiff menu 150
- 4.4.10Thickness menu 151
- 4.4.11Platen heater menu 151
- 4.4.12Dryer menu 152
- 4.4.16Media cut menu 154
- 4.4.17Printing mode menu 154
- 4.4.19Printing quality menu 155
- 4.4.20InterLace Setup menu 156
- 4.4.21Printing direction menu 156
- 4.4.22Printing repeat menu 156
- 4.4.23Repeat times menu 157
- 4.4.24Interval time menu 157
- 4.4.25Command setup menu 158
- 4.4.26Image resolution menu 158
- 4.4.27Online time out menu 159
- 4.4.28 Layout setup menu 159
- 4.4.29Joint printing menu 160
- 4.4.30Joint margin menu 160
- 4.4.31Function setup menu 161
- 4.4.32CMY→ 161
- 4.4.33Mirror menu 162
- 4.4.34Roll Media setup menu 162
- 4.4.35Roll media length menu 163
- 4.4.36Centronics menu 163
- 4.4.37Network menu 164
- 4.4.38Utility menu 164
- 4.4.39ErrorDisplay menu 165
- 4.4.40Media detection menu 165
- 4.4.41Media width menu 166
- 4.4.42Take-up mechanism menu 167
- 4.4.45Write mode menu 168
- 4.4.46Re-plot menu 169
- 170
- 4.4.48Re-name menu 171
- 4.4.49Format menu 172
- 173
- 173
- 4.4.51All Initialize menu 174
- 4.4.59Network Initialize menu 177
- 4.4.60Utility Initialize menu 178
- 4.4.62Data dump menu 178
- Status of the 181
- 4.5.3 Winding the roll media 182
- 4.5.4 Head cleaning 183
- 4.6 Operations after printing 186
- 5 MAINTENANCE 193
- <Memo> 194
- 5 Maintenance 195
- (2) Types 196
- (3) Refilling procedure 196
- 5.2.2 Replacing roll media 197
- Item name Model 204
- 5.3 Cleaning the printer 206
- 14. Turn the unit power OFF 215
- 15. Reattach the valve cover 215
- (1) Before the transfer 216
- 6 TROUBLESHOOTING 219
- 6 Troubleshooting 221
- (13) Cannot detect the media 225
- 6.3 Error messages 228
- 229
- (3) Other error messages 230
- 231
- 231
- 231
- 232
- 232
- 233
- 233
- 6.4 When media jams occur 234
- 7 APPENDIX 239
- Item Specifications 241
- 7.3 Interface Specifications 244
- 7.4 Options/Supply list 246
- Name Model Sales units 247
- Name Model 248
- 7.6 Glossary 252
- Cut-off line 259
- Operation Panel Table 260
- 263
- 263
Manuais e produtos relacionados com Digitalizar e Imprimir MUTOH PJ-2216NXE
(6 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais